Skip to content

Car care kit and maintenance essentials, chosen properly.

Fit & Fix

How to Check Tyre Tread Depth: A Simple Step-by-Step Guide

Check your tyre tread properly in minutes: legal limits, wear indicators, the 20p test, gauge readings and wear patterns that mean a trip to the garage.

Fit & Fix
Hands checking the tread of a car tyre in a workshop

The short answer: 1.6 mm is the law, 3 mm is the warning

Tread is the part of the tyre that pushes water out of the way so the rubber can stay in contact with the road. In the UK the legal minimum for cars and light vans is 1.6 mm across the central three-quarters of the tread width, all the way around the circumference. Below that you risk a fine of up to £2,500 and three penalty points, and that applies to each tyre that fails.

But 1.6 mm is the point at which a tyre becomes illegal, not the point at which it stops working. Wet braking distances climb sharply once tread drops below roughly 3 mm, which is why most tyre fitters and motoring organisations suggest planning a replacement at that point rather than waiting for the MOT to flag it.

So the practical answer is: measure with a gauge, take the lowest reading across the whole tread, write it down, and act at 3 mm.

UK legal minimum (cars and light vans)
1.6 mm across the central three-quarters of the tread width, around the entire circumference
Sensible replacement point
Around 3 mm — wet grip and resistance to aquaplaning fall away quickly below this
Wear indicator bars
Raised bars inside the main grooves, set at 1.6 mm; tread level with them means the tyre is at the limit
How often to check
Once a month and before any long journey, plus before the MOT
Penalty for a defective tyre
Up to £2,500 and three penalty points per tyre

What you need before you start

You do not need much, and none of it is expensive:

  • A tread depth gauge. A simple mechanical or digital gauge that reads in millimetres is the only tool that gives you an actual number. They cost very little at motor factors, and any tyre bay will check for you if you would rather not buy one.
  • A 20p coin. Useful for a quick check at the roadside or when you are looking at a car you are thinking of buying.
  • A rag and a torch. Grooves collect grit and stones, and a gauge will not seat properly on dirt.
  • A tyre pressure gauge. Wear patterns only make sense once you know the pressures are correct.
  • Something to record the numbers. Phone notes are fine — date, tyre position and the lowest reading.

How to check tyre tread, step by step

  1. 01 /

    Park somewhere flat and clean the tyre

    Handbrake on, engine off, on level ground — a driveway is ideal. If you have to use the roadside, keep well away from traffic and never kneel in a live lane. Wipe around the groove you are about to measure with a rag so grit and stones do not hold the gauge off the tread.

  2. 02 /

    Find the wear indicator bars

    Look down into the wide grooves that run around the tyre. Every so often you will see a raised bar running across the groove — those are the wear indicators, set at 1.6 mm. If the tread blocks are already level with those bars, the tyre is at the legal limit and needs replacing, and there is nothing more to measure.

  3. 03 /

    Take a gauge reading in a main groove

    Push the probe of the gauge down into the groove until the flat shoulder of the tool rests on the tread blocks either side. Read the scale, then take out the gauge and repeat. Some gauges read in millimetres and thirty-seconds of an inch, so make sure you are looking at the millimetre scale.

  4. 04 /

    Repeat around the wheel and across the tread

    Take at least three readings in the same groove at roughly evenly spaced points around the wheel, then repeat in a second groove nearer the inside edge. A tyre can pass at one point and fail at another, so the lowest number you find is the one that counts.

  5. 05 /

    Do the 20p check as a second opinion

    Push a 20p coin into a main groove with the banded edge facing you. If you can see the whole band sitting above the tread, the tyre is close to or past the limit. It is a rough guide rather than a measurement, but it is a useful cross-check and works well when you have no gauge to hand.

  6. 06 /

    Repeat on all four tyres and record the result

    Write down the lowest reading for each tyre with the date — front left, front right, rear left, rear right. Recording the numbers means you can see the rate of wear next month instead of guessing, and it shows you whether one tyre is losing tread faster than the others.

The 20p test: what it can and cannot tell you

The 20p trick works because the depth of the coin's outer band is close to the 1.6 mm legal limit, so a coin sitting in the groove gives you a visual reference near the point that matters. It is widely used because it needs nothing but a coin you probably have in your pocket.

What it cannot do is give you a figure. If the band sits just proud of the tread you know you are in the region of the limit, but you cannot tell 1.4 mm from 1.9 mm by eye, and that difference is the difference between legal and illegal. It also only checks the groove you happen to be looking at, and the inner edge of a tyre is exactly where wear is hardest to see.

Reading uneven wear: what the pattern is telling you

Depth is only half the story. Look across the full width of the tread and around the whole circumference — a tyre that reads 4 mm in the middle but 2 mm on the inner edge has a problem that a single gauge reading would hide.

Common tread wear patterns and what usually causes them
What you seeMost likely causeWhat to do
Worn down the centre, shoulders intactOver-inflation, or a lot of steady motorway mileageCheck pressures cold once a month against the vehicle plate; replace earlier than the edge wear suggests
Worn on both outer edgesUnder-inflation, or frequent heavy loadsCorrect the pressures and check them with the car loaded as you normally drive it
Worn on one edge onlyWheel alignment or camber out of specificationHave the geometry checked; a new tyre will wear the same way if the cause is not fixed
Patchy, scalloped or cuppedWorn suspension components or a wheel out of balanceAsk a garage to check dampers, bushes and balance
A single flat spotHeavy braking, or the car standing for monthsIf you can feel it through the wheel or hear it, the tyre may need replacing

Look past the tread: sidewalls, age and pressures

While you are down at wheel level, spend another minute on the rest of the tyre:

  • Sidewalls. Look for cuts, cracks, grazes and anything embedded in the rubber. A bulge or blister in the sidewall means the internal structure is damaged — that tyre should not be driven on.
  • Objects in the tread. Screws and nails can sit flush and hold pressure for weeks before a slow puncture appears. Do not pull out something that is holding air; get it looked at.
  • Age. The DOT code on the sidewall ends in four digits — the week and year of manufacture. Many tyre and vehicle makers advise replacing tyres at around ten years old regardless of tread, and inspecting them closely from about five.
  • Pressures. Use the figures on the plate inside the driver's door shut or fuel flap, not the maximum pressure moulded into the sidewall. Check cold, and remember that under-inflation both wears the edges and heats the tyre up.

Common mistakes that give a false reading

  • Measuring only the outer groove. On cars with lowered suspension or a lot of negative camber, the inner edge wears fastest and is the hardest to see. Reach around and check a groove nearer the inside.
  • Taking one reading per tyre. A locked wheel or a heavy kerb strike can wear one section far more than the rest. Always take three readings around the circumference.
  • Assuming the wear indicators are a measurement. They mark the legal limit, nothing more. They tell you when you have already got there.
  • Judging from a photograph. Depth does not photograph reliably, and lighting makes a 2 mm groove look like a 4 mm one.
  • Checking a hot tyre after a run. Tread does not change with heat, but pressures do, and a hot pressure reading will send you chasing a problem that is not there.
  • Skipping the rears. Rear tyres wear more slowly and get looked at least. On a front-wheel-drive car they may be the oldest rubber on the vehicle.

Deciding when to replace, and what to ask for

At or near 1.6 mm, the tyre is illegal or about to be and should come off before the car is driven in the wet. Between 1.6 mm and 3 mm, it is legal but compromised — fine for dry local driving in the short term, worth booking in before the weather turns. Above 3 mm, keep measuring monthly and watch the trend rather than the single number.

A few practical points when you do replace:

  • Replace in pairs on the same axle where you can, so braking and grip stay balanced side to side.
  • If you are only replacing two, most fitters put the new pair on the rear — a rear tyre losing grip is much harder to correct than a front one.
  • If the old tyre wore unevenly, get the alignment checked at the same time, or the new tyre will follow the same pattern.
  • Ask for the pressures to be set and re-check them cold a week later, once the tyres have settled.

Frequently asked questions

Can I check tyre tread with a 20p coin?

Yes, as a rough guide. Push the coin into a main groove: if the whole outer band sits above the tread, you are at or near the limit. It will not tell you whether you are at 1.4 mm or 1.9 mm, so use a gauge to confirm.

What is the legal tyre tread depth in the UK?

For cars and light vans it is 1.6 mm across the central three-quarters of the tread width, around the entire circumference. Motorcycles over 50cc must have at least 1 mm across three-quarters of the width.

How often should I check my tyre tread?

Once a month is a good habit, plus before long journeys, before winter, and ahead of the MOT. Checking at the same time as you check pressures means neither job gets forgotten.

Will low tread fail an MOT?

Yes. Tread depth is part of the MOT test, and a tyre below the legal minimum is a fail. A tyre that is legal but close to the limit can also attract an advisory, which is a useful early warning.

How many miles should a set of tyres last?

There is no reliable figure — wear depends on the tyre, the car, the load you carry, how well the pressures are kept and the kind of roads you use. That is why depth is measured rather than estimated from mileage.

Search