The short answer
Adding air to a tyre takes a few minutes once you know the figure you are aiming for. Park near the air machine so the hose reaches the valve, take the cap off, check what the tyre is currently holding, then add air in short bursts until it matches the pressure listed in your handbook or on the sticker inside the driver's door pillar. Screw the cap back on and repeat on the other three tyres.
The number moulded into the tyre sidewall is a maximum, not a target — it tells you what the tyre can take, not what your car needs.
What you need before you start
You do not need much, but having it to hand makes the job quick:
- The correct pressure figure for your car, from the handbook, the door pillar sticker or the fuel filler flap.
- An air supply: a forecourt air line, a foot pump, or a 12V compressor that plugs into the lighter socket.
- A pressure gauge, ideally a separate one. The gauge built into a forecourt machine has usually had a hard life and may read a little off.
- Somewhere safe for the valve caps, plus a cloth to wipe grit off the valve before you connect anything.
- A torch if you are checking after dark, and gloves if the wheels are grubby.
Find the right pressure for your car
There are three places the numbers live, and they do not all mean the same thing. The car maker's figures are the ones to set your tyres to.
| Where to look | What it tells you | How to use it |
|---|---|---|
| Door pillar or fuel flap sticker | The car maker's cold pressures, often split front and rear, plus a higher set for a full load | Your day-to-day reference |
| Handbook | More detail, sometimes covering different wheel sizes, towing and heavy loads | Use it when the sticker is missing or unclear |
| Tyre sidewall | The maximum load and pressure the tyre is rated for | A limit only — never a target |
Step by step: putting air in a tyre
-
01 /
Park within reach and secure the car
Pull up so the hose comfortably reaches the valve on the tyre you are filling. Switch the engine off, apply the handbrake, and use your hazard lights if the forecourt is busy so other drivers give you room.
-
02 /
Remove the valve cap and keep it safe
Unscrew the cap and put it in your pocket rather than on the floor or the roof of the car. Wipe any dirt or moisture off the valve with a cloth — grit pushed into the valve is the usual cause of a slow leak afterwards.
-
03 /
Check the pressure it is holding now
Press the gauge squarely onto the valve and hold it there for a moment. Note the reading. If the tyre is visibly flat at the bottom, do not drive on it; inflate cautiously and get it looked at.
-
04 /
Set the machine to your target
Some forecourt machines let you dial in the pressure and stop automatically; others simply deliver air. If there is no preset, you will be adding air in short bursts and checking as you go.
-
05 /
Push the chuck onto the valve squarely
You will hear a brief hiss as the connector seats. A loud, constant leak means it is not sitting straight — pull it off and try again rather than wiggling it about, which can damage the valve.
-
06 /
Add air in short bursts
Two or three seconds at a time is plenty on a car tyre. Release, check with your gauge, and repeat until you reach the target. Overshooting is easy with a fast forecourt line; a quick press on the gauge's bleed button lets a little air back out.
-
07 /
Refit the valve cap
Screw it on finger tight. The cap is not just cosmetic — it keeps dirt and water out of the valve core, which is what keeps the air in.
-
08 /
Reset the monitoring system if you have one
Many cars need the tyre pressure monitoring system resetting after inflating. The procedure varies, so check your handbook; some cars do it from a menu, others have a button in the glovebox or near the handbrake.
When you have to inflate warm tyres
A tyre that has just covered twenty miles will read higher than the same tyre when cold, because the air inside has heated up and expanded. That is normal and not a fault.
If you have to top up mid-journey, aim a little above the cold figure rather than below it, and never bleed a warm tyre down to its cold number — you would be driving away on an under-inflated tyre that heats up even more. Recheck when the car has been standing for a couple of hours and adjust then.
What commonly goes wrong, and how to fix it
- The valve hisses after you take the chuck off. A bit of grit or a slightly loose valve core. Reconnect the chuck briefly to blow it clear; if it keeps leaking, the core needs tightening or replacing at a garage.
- The machine's gauge and yours disagree. Gauges drift out of calibration. Trust a decent separate gauge, and if two of them still disagree wildly, try a third before you start chasing a problem.
- You have overshot the pressure. Let air out in short presses rather than one long one, checking between each.
- The tyre will not hold what you put in. A puncture, a corroded rim seal or a leaking valve. Pumping it up again only hides the problem — get it checked properly.
- The cap will not go back on. It is probably cross-threaded. Turn it anticlockwise until you feel it drop into its starting thread, then screw it on clockwise.
- The chuck will not seal at all. Push it on straight and hold it steady; forcing or twisting it can damage the valve core.
Safety points worth knowing
Keep your face and body to the side of the tyre rather than leaning over it while the line is connected, and never exceed the maximum pressure on the sidewall. If a tyre is losing pressure repeatedly, treat it as a repair job rather than something to keep topping up — under-inflation affects grip, braking and fuel use, and it overheats the sidewall.
Keeping tyres at the right pressure
Pressure is not a set-and-forget figure. Air escapes slowly through the rubber and the valve, and cooler weather drops the reading further, so a monthly check with your own gauge catches most problems before they show up as an uneven, scrubbed edge on the tread.
Check the spare at the same time — space-saver tyres often run at a much higher pressure than the road wheels, and that figure is in the handbook or on a sticker on the wheel itself. If the dashboard warning light comes on, check all four tyres with a gauge rather than assuming the sensor is faulty; sensors are usually right.
Common questions about putting air in a tyre
Can I use a foot pump instead of a forecourt machine?
Yes. Any pump that can reach your car's pressure will do. A foot pump or 12V compressor takes longer and usually has a rough gauge, so check the final figure with a separate gauge rather than trusting the one on the pump.
How do I know a tyre needs air if it still looks fine?
Looks are unreliable — a tyre can lose several pounds of pressure and still sit normally on the ground. Use a gauge once a month, and treat a dashboard warning light as a prompt to check all four tyres.
Should I put air in a tyre with a slow puncture?
You can top it up to get you to a garage, but keep the speed and distance down and check it again soon. A tyre that keeps losing pressure needs repairing or replacing; repeated topping up just delays it.
What do PSI and bar mean?
Both are units of pressure. One bar is roughly 14.5 PSI. Use whichever unit your handbook quotes and make sure the air machine is set to the same one before you start.
Does the spare tyre need air too?
Yes — check it when you check the other four. Space savers often need considerably more pressure than the road tyres, so use the figure in the handbook or on the wheel sticker, not the one on the door pillar.



